| Input, current | Yes |
| Input, voltage | Yes |
| Input, resistor | No |
| Input, resistance thermometer | No |
| Input, thermocouple | No |
| Input signal, configurable | Yes |
| Output, current | No |
| Output, voltage | No |
| Output signal configurable | No |
| Analogue inputs configurable | Yes |
| Analogue outputs configurable | No |
| Type of electric connection | Screw-/spring clamp connection |
| Output range | -10â⬦10V, 0â⬦10V, 0â⬦5V, 0â⬦20 Ma |
| Module keying | Electronic, software configurable |
| Module error over full temperature range | 0.1 % |
| Module conversion method | R-Ladder DAC, monotonicity with no missing codes |
| Open circuit detection | Current output = Yes |
| Drive capability | Current output = 0...1000 é, Voltage output =>1000 é |
| Short circuit detection | Voltage output = Yes |
| Data format | IEEE 32-bit floating point |
| Wire category | 2 - on signal ports |
| Overvoltage protection | ñ30V DC (voltage/current) |
| Settling time | <2 ms to 95% of final value with resistive loads |
| Total backplane power | Voltage mode = 6.3 W, Current mode with 250 é loads = 6.3 W, Current mode with 500 é loads = 7.6 W, Current mode with 750 é loads = 9.2 W, Current mode with 1000 é loads = 10.2 W |
| Module scan time | 1 ms minimum |
| Thermal dissipation | Voltage mode = 18.4 BTU/hr, Current mode with 250 é loads = 18.4 BTU/hr, Current mode with 500 é loads = 19.8 BTU/hr, Current mode with 750 é loads = 22.2 BTU/hr, Current mode with 1000 é loads = 22.9 BTU/hr |
| Current draw | 200 mA @ 5.1V, Voltage or current mode with 250 é loads = 220 mA @ 24V, Current mode with 500 é loads = 275 mA @ 24V, Current mode with 750 é loads = 340 mA @ 24V, Current mode with 1000 é loads = 385 mA @ 24V |
| Inputs | Eight isolated channels - any combination of voltage or current mode |
| Power dissipation | Voltage mode: 5.4 W (18.4 BTU/hr), Current mode with 250 é loads: 5.4 W (18.4 BTU/hr), Current mode with 500 é loads: 5.8 W (19.8 BTU/hr), Current mode with 750 é loads: 6.5 W (22.2 BTU/hr), Current mode with 1000 é loads: 6.7 W (22.9 BTU/hr) |
| Resolution | 16 bit, ñ10.5V (0.32 mV/count), 0...10.5V (0.16 mV/count), 0...5.25V (0.08 mV/count), 0...21 mA (0.32 üA/count) |
| Wire size | 0.33...2.1 mmò (22...14 AWG) solid or stranded shielded copper wire, rated at 90 ðC (194 ðF) or greater, 1.2 mm (3/64 in.) insulation maximum |
| Calibrated accuracy | 0.05% @ 25 ðC (77 ðF) |
| Suitable for safety functions | No |
| Output impedance | 46 é (Current output) |
| Surrounding air temperature, max | 60 ðC |
| North American temperature code | T4 |
| Emissions | IEC 61000-6-4 |
| ESD immunity | 6 kV contact discharges, 8 kV air discharges |
| EFT/B immunity | ñ4 kV at 5 kHz on signal ports |
| Relative humidity | 5...95% noncondensing |
| Conducted RF immunity | 10V rms with 1 kHz sine-wave 80% AM from 150 kHz...80 MHz |
| Surge transient immunity | ñ2 kV line-earth (CM) on shielded signal ports |
| Operating temperature | 0 to 60 ðC |
| Radiated RF immunity | 10 V/m with 1 kHz sine-wave 80% AM from 80...2000 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 900 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 1890 MHz, 3 V/m with 1 kHz sine-wave 80% AM from 2000...2700 MHz |
| Nonoperating temperature | -40 ðC |
| RTB keying | User-defined mechanical |
| Vibration | 2 G @ 10...500 Hz |
| Shock | Operating: 30 G, Non operating: 50 G |
| Slot width | 1 |
| Isolation voltage | 250V (continuous), reinforced insulation type, outputs to backplane, 250V (continuous), basic insulation type, output to output |
| IEC temperature code | T4 |
| Enclosure type rating | None (open-style) |
Available 
