1756-IF8I ROCKWELL AUTOMATION

Input, current	Yes
Input, voltage	Yes
Input, resistor	No
Input, resistance thermometer	No
Input, thermocouple	No
Input signal, configurable	Yes
Output, current	No
Output, voltage	No
Output signal configurable	No
Analogue inputs configurable	Yes
Analogue outputs configurable	No
Type of electric connection	Screw-/spring clamp connection
Channel bandwidth	Notch Filter configuration dependent
Module keying	Electronic, software configurable
Module error over full temperature range	0.1 %
Module conversion method	Sigma-Delta
Input range	-10...10V, 0Ã¢Ã¢¬¦10V, 0...5V, 0...20 mA
Data format	IEEE 32-bit floating point
Wire category	2 - on signal ports
Overvoltage protection	Ã±30V DC maximum
Common mode noise rejection	120 dB @ 50/60 Hz
Normal mode noise rejection	80 dB @ 60 Hz
Module input scan time, min	1 ms
Voltage and current ratings	Backplane: 5.1V DC 200 mA, 24V DC 400 mA, Input voltage: -10V to +10V, 0V to 10V, 0V to 5V, Input current: 0 mA to 20 mA, Output current: 0 mA to 20 mA
Settling time	Notch Filter configuration dependent
Total backplane power	Voltage/Non-sourcing current mode: 4.6 W, Sourcing current mode: 10.6 W
Thermal dissipation	Voltage mode: 15.7 BTU/hr, Non-sourcing current mode: 17.4 BTU/hr, Sourcing current mode: 24.9 BTU/hr
Current draw	200 mA @ 5.1V, Voltage/Non-sourcing current mode: 150 mA @ 24V, Sourcing current mode: 400 mA @ 24V (In sourcing current mode, the channel provides loop power.)
Inputs	Eight isolated channels - any combination of voltage or current mode
Power dissipation	Voltage mode: 4.6 W (15.7 BTU/hr), Non-sourcing current mode: 5.1 W (17.4 BTU/hr), Sourcing current mode: 7.3 W (24.9 BTU/hr)
Resolution	24 bit, Ã±10.5V (1.49 Ã¼V/count), 0...10.5V (1.49 Ã¼V/count), 0...5.25V (1.49 Ã¼V/count), 0...21 mA (2.99 nA/count)
Wire size	0.33...2.1 mmÃ² (22...14 AWG) solid or stranded shielded copper wire rated at 90 Ã°C (194 Ã°F), or greater, 1.2 mm (3/64 in.) insulation maximum
Calibrated accuracy	0.05% @ 25 Ã°C (77 Ã°F)
Open circuit detection time	5 s
Suitable for safety functions	No
Onboard data alarming	Yes
Scaling to engineering units	Yes
Real-time channel sampling	Yes
Sourcing voltage, min	20V DC
Sourcing voltage, max	36V DC (open circuit)
Sourcing current, max	Current limited <45 mA (IN_x/I/SRC to RTN_x)
Surrounding air temperature, max	60 Ã°C
North American temperature code	T4
Emissions	IEC 61000-6-4
ESD immunity	6 kV contact discharges, 8 kV air discharges
EFT/B immunity	Ã±4kV at 5 kHz on shielded signal ports
Relative humidity	5...95% noncondensing
Conducted RF immunity	10V rms with 1 kHz sine wave 80% AM from 150 kHz...80 MHz on shielded signal ports
Surge transient immunity	Ã±2 kV line-earth (CM) on shielded signal ports
Operating temperature	0 to 60 Ã°C
Radiated RF immunity	10 V/m with 1 kHz sine-wave 80% AM from 80...2000 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 900 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 1890 MHz, 3 V/m with 1 kHz sine-wave 80% AM from 2000...2700 MHz
Nonoperating temperature	-40 Ã°C
RTB keying	User-defined mechanical
Vibration	2 G @ 10...500 Hz
Shock	Operating: 30 G, Non operating: 50 G
Slot width	1
Input impedance	Voltage mode: 1 GÃ© approximately (powered), Voltage mode: 7500 Ã© approximately (unpowered), Current mode: 125 Ã© approximately
Isolation voltage	250V (continuous), reinforced insulation type, inputs to backplane, 250V (continuous), basic insulation type, input to input
IEC temperature code	T4
Enclosure type rating	None (open-style)