Industrial Automation

Mechatronics

Industrial Safety

Panel Components

Sensors and Systems of Vision

Pneumatics

Network Comunications

Automation Cables

Design Software

Access services

Enter your reserved area

Access services

Enter your reserved area

PROSOFT TECHNOLOGY PLX31-EIP-PND
PROSOFT TECHNOLOGYAvailable

EtherNet/IP™ to PROFINET IO Device Gateway

Product Code: PLX31-EIP-PND
Partner cod.: PLX31-EIP-PND
PROSOFT TECHNOLOGY


Diminuisci la quantità
Aumenta la quantità
Tecnichal data
Technical Specs
Description
Tecnichal data
Features and Benefits
Embedded EDS Add-On Profile allows for simplified integration and reduced configuration time for Rockwell Automation PACs.
No ladder programming is required when using I/O connections.
Multiple I/O connections allow you to set different RPIs for status and control data, enabling Ethernet bandwidth optimization.
Communication via an I/O connection provides guaranteed data delivery and enables the PAC to monitor for communication faults.
SD card slot (SD card optional) is used for storing configuration files in the event of a disaster.
ProSoft Discovery Service allows your PC to find the gateway and change its default IP address without being on the same subnet.
Video setup tutorial provided at psft.com/Ap5
Technical Specs
Specifications
Number of Class 3 Server Connections:5
Supported PLC Types:PLC2, PLC5, SLC, CLX, CMPLX
Supported Message Types:PCCC and CIP
Number of Class 3 Client Connections:Connected - 2
Number of Class 3 Client Connections:Unconnected - 1
Number of Class 1 I/O Connections:8
Max I/O connection sizeIn/Out:496/496 bytes
Max RPI time:10 ms per connection
CIP Services Supported:0x4C - CIP Data Table Read
CIP Services Supported:0x4D - CIP Data Table Write
Command List:Support for 100 commands per Client, each configurable for command type, IP address, register to/from addressing and word/bit count.
Command Sets:PLC-2/PLC-3/PLC5 Basic Command Set
Command Sets:PLC5 Binary Command Set
Command Sets:PLC5 ASCII Command Set
Command Sets:SLC500 Command Set
Hardware
Power Supply:24 VDC nominal
Power Supply:10 to 36 VDC allowed
Power Supply:Positive, Negative, GND Terminals
Current Load:24 VDC nominal @ 300 mA
Current Load:10 to 36 VDC @ 610 mA maximum
Operating Temperature:-25°C to 70°C (-13°F to 158°F)
Storage Temperature:-40°C to 80°C (-40°F to 176°F)
Shock:IEC 60068-2-27; 15G @ 11ms, 3-Axis (Operational)
Shock:IEC 60068-2-27; 30G @ 18ms, 3-Axis (Non-Operational)
Vibration:IEC 60068-2-6; 5G @ 10 to 150 Hz
Relative Humidity:5% to 95% RH with no condensation
Dimensions (H x W x D):5.38 x 1.99 x 4.38 in 13.67 x 5.05 x 11.13 cm
LED Indicators:Configuration (CFG), Error (ERR), Power (PWR), Hardware Fault (FLT), Network Status (NS), EtherNet/IP™ Class I or Class III Connection Status (EtherNet/IP Only) Module Status (MS), ModuleConfiguration Status (EtherNet/IP Only) Ethernet Communication Port Link/Activity, and 100 mbit
Ethernet Port:10/100Mbit half-duplex RJ45 Connector Electrical Isolation 1500 Vrms at 50 to 60 Hz for 60 seconds, applied as specified in section 5.3.2 of IEC 60950: 1991 Ethernet Broadcast Storm Resiliency is less than or equal to 5000 [ARP] frames-per-second and less than or equal to 5 minutes duration
Shipped With Each Unit:2.5 mm screwdriver
Shipped With Each Unit:ProSoft Solutions DVD
Shipped With Each Unit:J180 Power Connector
Shipped With Each Unit:5’ straight-through Ethernet cable
Description
The EtherNet/IP™ to PROFINET® IO Device (slave) gateway offers bi-directional data transfers between EtherNet/IP™ controllers and a PROFINET® IO controller. The EtherNet/IP™ Driver supports I/O connections for guaranteed data delivery or Message instructions to send data to/from the PACs. The gateway supports 1440 bytes of input data and 1440 bytes of output data for larger applications. In addition, the gateway’s multiple I/O connections, allow you to set different RPIs for control data and module diagnostics, enabling you to optimize your Ethernet bandwidth.