| Input data | AC operation Nominal input voltage range: 100 VAC ... 240 VAC Input voltage range: 85 VAC ... 264 VAC Input voltage range AC: 85 VAC ... 264 VAC Voltage type of supply voltage: AC Inrush current: < 40 A (typical) Inrush current integral (I2t): < 1.5 A2s Frequency range (fN): 50 Hz ... 60 Hz ±10% Mains buffering time: > 20 ms (120VAC) > 100 ms (230 V AC) Current consumption: 2.1 A (100VAC) 0.95 A (240VAC) Nominal power consumption: 242.6 VA Protective circuit: Transient surge protection; Varistor Power factor (cos phi): 0.47 Typical response time: < 1 s Input fuse: 4 A (slow-blow, internal) Recommended breaker for input protection: 6 A ... 16 A (Characteristics B, C, D, K) |
| Output data | Efficiency: typ. 88 % (120VAC) typ. 89 % (230 V AC) Output characteristic: HICCUP Nominal output voltage: 24 VDC ±1% Nominal output current (IN): 4.2 A (-25°C...55°C) Derating: 55°C ... 70°C (2.5%/K) Feedback voltage resistance: < 35 VDC Protection against overvoltage at the output (OVP): ⤠35 VDC Control deviation: < 1 % (change in load, static 10 % ... 90 %) < 2 % (Dynamic load change 10 % ... 90 %, 10 Hz) < 0.1 % (change in input voltage ±10 %) Residual ripple: < 30 mVPP (with nominal values) Short-circuit-proof: yes No-load proof: yes Output power: 100 W Maximum no-load power dissipation: < 0.5 W Power loss nominal load max.: < 11 W Rise time: < 0.5 s (UOUT (10 % ... 90 %)) Response time: < 2 ms Connection in series: yes |
| Connection data | Input Connection method: Screw connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 14 Stripping length: 8 mm Screw thread: M3 Tightening torque, min: 0.5 Nm Tightening torque max: 0.6 Nm Output Connection method: Screw connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 14 Stripping length: 8 mm Screw thread: M3 Tightening torque, min: 0.6 Nm Tightening torque max: 0.8 Nm |
| Signaling | Types of signaling: LED |
| Electrical properties | Number of phases: 1.00 Insulation voltage input/output: 4 kV AC (type test) 3 kV AC (routine test) |
| Product properties | Product type: Power supply Product family: UNO POWER MTBF (IEC 61709, SN 29500): > 738000 h (40°C) Insulation characteristics Protection class: II (in closed control cabinet) Degree of pollution: 2 |
| Dimensions | Width: 55 mm Height: 90 mm Depth: 84 mm Installation dimensions Installation distance right/left: 0 mm / 0 mm Installation distance top/bottom: 30 mm / 30 mm |
| Mounting | Mounting type: DIN rail mounting Assembly instructions: alignable: 0mm horizontally, 30mm vertically Mounting position: horizontal DIN rail NS 35, EN 60715 With protective coating: No |
| Material specifications | Flammability rating according to UL94 (housing / terminal blocks): V0 Housing material: Plastic Polycarbonate Type of housing: Polycarbonate Foot latch material: POM (Polyoxymethylene) |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25°C ... 70°C (> 55°C Derating: 2.5 %/K) Ambient temperature (storage/transport): -40°C ... 85°C Ambient temperature (start-up type tested): -40°C Climatic class: 3K3 (in acc. with EN 60721) Max. permissible relative humidity (operation): ⤠95 % (at 25°C, non-condensing) Shock: 18 ms, 30g, in each space direction (according to IEC 60068-2-27) Vibration (operation): < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) 15 Hz ... 150 Hz, 2.3g, 90 min. |
| Standards and regulations | Budgetary standard: IEC 60335-1 Standard â Electronic equipment for use in electrical power installations and their assembly into electrical power installations: EN50178/VDE0160 (PELV) Standard â Limitation of mains harmonic currents: EN61000-3-2 Standard - Electrical safety: IEC 62368-1(SELV) Standard â Safety extra-low voltage: IEC 62368-1 (SELV) und EN60204-1 (PELV) Standard - Safe isolation: DINVDE0100-410 Standard - Safety of transformers: EN61558-2-16 Approval - requirement of the semiconductor industry with regard to mains voltage dips: EN61000-4-11 |
| Approvals | CSA: CAN/CSA-C22.2 No.60950-1-07 CSA-C22.2 No.107.1-01 CAN/CSA-C22.2 No. 213 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location) UL approvals: UL/C-UL listed UL508 UL/C-UL Listed ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location) UL/C-UL Recognized UL60950-1 Conformity/Approvals SIL in accordance with IEC 61508: 0 |
| EMC data | Low Voltage Directive: Conformance with Low Voltage Directive 2014/35/EC EMC requirements for noise emission: EN61000-6-3 EN61000-6-4 EMC requirements for noise immunity: EN61000-6-1 EN61000-6-2 Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Electrostatic discharge Standards/regulations: EN61000-4-2 Electrostatic dischargeâ Contact discharge: 6 kV (Test Level 3) Discharge in air: 8 kV (Test Level 3) Comments: Criterion B Electromagnetic HF field Standards/regulations: EN61000-4-3 Electromagnetic HF fieldâ Frequency range: 80 MHz ... 1 GHz 1 GHz ... 6 GHz Test field strength: 10 V/m (Test Level 3) Comments: Criterion A Fast transients (burst) Standards/regulations: EN61000-4-4 Fast transients (burst)â Input: 4 kV (Test Level 4 - asymmetrical) Output: 2 kV (Test Level 3 - asymmetrical) Comments: Criterion A Surge voltage load (surge) Standards/regulations: EN61000-4-5 Input: 2 kV (Test Level 3 - symmetrical) 4 kV (Test Level 4 - asymmetrical) Output: 1 kV (Test Level 2 - symmetrical) 2 kV (Test Level 1 - asymmetrical) Comments: Criterion B Conducted interference Standards/regulations: EN61000-4-6 Conducted interferenceâ Input/Output: asymmetrical Frequency range: 0.15 MHz ... 80 MHz Comments: Criterion A Voltage: 10 V (Test Level 3) Voltage dips Standards/regulations: EN61000-4-11 Emitted interference Standards/regulations: EN61000-6-3 Radio interference voltage in acc. with EN 55011: EN55011 (EN55022) classB used in industry and residential area / EMC1 Emitted radio interference in acc. with EN 55011: EN 55011 (EN 55022) class B used in industry and residential area / EMC 1 Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself. |
Di seguito alcuni articoli correlati a quello che stai vedendo
