Disponibile 
| Input data | AC operation Network type: Star network Nominal input voltage range: 3x 400 VAC ... 500 VAC Input voltage range: 3x 400 VAC ... 500 VAC -20%...+15% Typical national grid voltage: 3x 400 VAC 3x 480 VAC Voltage type of supply voltage: AC Inrush current: ⤠30 A (typical) Inrush current integral (I2t): < 1.1 A2s Inrush current limitation: 35 A (after 1ms) AC frequency range: 50 Hz ... 60 Hz Frequency range (fN): 50 Hz ... 60 Hz ±5Hz Mains buffering time: > 10 ms (400VAC) > 20 ms (480VAC) Current consumption: 3x 1.9 A (400VAC) 3x 1.7 A (500 V AC) Nominal power consumption: 1335.1 VA Protective circuit: Transient surge protection; Varistor Power factor (cos phi): 0.77 Typical response time: < 1 s Input fuse: 6.3 A (internal (device protection)) Recommended breaker for input protection: 10 A ... 16 A (Characteristics B, C, D, K) Discharge current to PE: < 3.5 mA < 2.5 mA (550 V AC, 60 Hz) |
| Output data | Efficiency: > 94.6 % (400VAC) > 94.3 % (480VAC) Output characteristic: U/I with dynamic load reserve Nominal output voltage: 72 VDC ±1% Setting range of the output voltage (USet): 70 VDC ... 85 VDC (>72 VDC, constant capacity restricted) Nominal output current (IN): 14 A Dynamic Boost (IDyn.Boost): 21 A (5 s) Derating: > 60°C ... 70°C (2.5%/K) Feedback voltage resistance: < 105 VDC Protection against overvoltage at the output (OVP): ⤠105 VDC Control deviation: < 1 % (change in load, static 10 % ... 90 %) < 3 % (Dynamic load change 10 % ... 90 %, 10 Hz) < 0.1 % (change in input voltage ±10 %) Residual ripple: ⤠300 mVPP Short-circuit-proof: yes No-load proof: yes Output power: 1008 W 1512 W Maximum no-load power dissipation: < 7 W (400VAC) Power loss nominal load max.: < 58 W (400VAC) Short-circuit current: < 23.5 ADC (Permanent) Rise time: ⤠2 ms (UOUT (10 % ... 90 %)) Connection in parallel: yes Connection in series: yes Signal: DC OK Continuous load current: 100 mA Signal relay 13/14 Default: closed Digital: 30 VAC 30 VDC 100 mA |
| Connection data | Input Connection method: Push-in connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 4 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 4 mm² Single conductor/flexible terminal point with ferrule with plastic sleeve, min.: 0.2 mm² Single conductor/flexible terminal point with ferrule with plastic sleeve, max.: 2.5 mm² Single conductor/flexible terminal point with ferrule without plastic sleeve, min.: 0.2 mm² Single conductor/flexible terminal point with ferrule without plastic sleeve, max.: 2.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 12 Stripping length: 10 mm Output Connection method: Push-in connection Conductor cross section, rigid min.: 0.75 mm² Conductor cross section, rigid max.: 16 mm² Conductor cross section flexible min.: 0.75 mm² Conductor cross section flexible max.: 16 mm² Single conductor/flexible terminal point with ferrule with plastic sleeve, min.: 0.75 mm² Single conductor/flexible terminal point with ferrule with plastic sleeve, max.: 10 mm² Single conductor/flexible terminal point with ferrule without plastic sleeve, min.: 0.75 mm² Single conductor/flexible terminal point with ferrule without plastic sleeve, max.: 16 mm² Conductor cross section AWG min.: 20 Conductor cross section AWG max.: 4 Stripping length: 18 mm Signal Connection method: Push-in connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 0.75 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 1.5 mm² Single conductor/flexible terminal point with ferrule with plastic sleeve, min.: 0.2 mm² Single conductor/flexible terminal point with ferrule with plastic sleeve, max.: 0.75 mm² Single conductor/flexible terminal point with ferrule without plastic sleeve, min.: 0.2 mm² Single conductor/flexible terminal point with ferrule without plastic sleeve, max.: 1 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 18 Stripping length: 8 mm |
| Signaling | Types of signaling: LED Floating signal contact Signal output: LED status indicator Signalization designation: DC OK Status display: LED Color: green DC OK: UOUT > 0.95 x UN (UN = 72VDC) |
| Electrical properties | Number of phases: 3.00 Insulation voltage input/output: 3 kV AC (type test) 1.5 kV AC (routine test) |
| Product properties | Product type: Power supply Product family: TRIO POWER MTBF (IEC 61709, SN 29500): > 1730000 h (25°C) > 1051000 h (40°C) > 510000 h (60°C) Insulation characteristics Protection class: I (in closed control cabinet) Degree of pollution: 2 |
| Dimensions | Width: 110 mm Height: 130 mm Depth: 160 mm Installation dimensions Installation distance right/left: 0 mm / 0 mm Installation distance top/bottom: 50 mm / 50 mm |
| Mounting | Mounting type: DIN rail mounting Assembly instructions: alignable: horizontally 0 mm (⤠40°C) 10 mm (⤠70°C), vertically 50 mm Mounting position: horizontal DIN rail NS 35, EN 60715 With protective coating: No |
| Material specifications | Flammability rating according to UL94 (housing / terminal blocks): V0 Housing material: Plastic Type of housing: Aluminum (AlMg3) Hood version: Polycarbonate |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25°C ... 70°C (>60°C Derating: 2,5%/K) Ambient temperature (storage/transport): -40°C ... 85°C Ambient temperature (start-up type tested): -40°C Maximum altitude: ⤠4000 m (>2000m, Derating: 10%/1000m) Climatic class: 3K3 (in acc. with EN 60721) Max. permissible relative humidity (operation): ⤠95 % (at 25°C, non-condensing) Shock: 11ms, 15g, in each space direction (according to IEC 60068-2-27) Vibration (operation): < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) 15 Hz ... 150 Hz, 0.7g, 90 min. |
| Standards and regulations | Standard â Limitation of mains harmonic currents: EN61000-3-2 Standard - Electrical safety: IEC 61010-2-201 Standard - Safe isolation: DINVDE0100-410 Standard - Safety of transformers: EN61558-2-16 (air clearances and creepage distances only) Overvoltage category EN 61010-1: II(â¤2000m) |
| Approvals | UL approvals: UL/C-UL Listed UL61010-1 Conformity/Approvals SIL in accordance with IEC 61508: 0 |
| EMC data | Low Voltage Directive: Conformance with Low Voltage Directive 2014/35/EC Interference emission: Interference emission in accordance with EN61000-6-3 (residential and commercial) and EN61000-6-4 (industrial) EMC requirements for noise immunity: EN61000-6-1 EN61000-6-2 Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Conducted noise emission: EN55016-2-1 EN61000-6-4 (Class A) Noise emission: EN 55011 (EN 55022) EN55016-2-3 EN61000-6-4 (Class A) Harmonic currents Standards/regulations: EN55016-2-3 EN61000-3-2 (Class A) Flicker Standards/regulations: EN61000-3-3 Electrostatic discharge Standards/regulations: EN61000-4-2 Electrostatic dischargeâ Contact discharge: 6 kV (Test Level 3) Discharge in air: 8 kV (Test Level 3) Comments: Criterion A Electromagnetic HF field Standards/regulations: EN61000-4-3 Electromagnetic HF fieldâ Frequency range: 80 MHz ... 1 GHz 1 GHz ... 2 GHz 2 GHz ... 6 GHz Test field strength: 10 V/m (Test Level 3) Comments: Criterion A Fast transients (burst) Standards/regulations: EN61000-4-4 Fast transients (burst)â Input: 4 kV (Test Level 3 - asymmetrical) Output: 2 kV (Test Level 3 - asymmetrical) Signal: 2 kV (Test Level 3 - asymmetrical) Comments: Criterion A Surge voltage load (surge) Standards/regulations: EN61000-4-5 Input: 2 kV (Test Level 4 - symmetrical) 4 kV (Test Level 4 - asymmetrical) Output: 1 kV (Test Level 3 - symmetrical) 2 kV (Test Level 3 - asymmetrical) Signal: 1 kV (Test Level 2 - asymmetrical) Comments: Criterion A Conducted interference Standards/regulations: EN61000-4-6 Conducted interferenceâ Input/Output: asymmetrical Frequency range: 0.15 MHz ... 80 MHz Comments: Criterion A Voltage: 10 V (Test Level 3) Voltage dips Standards/regulations: EN61000-4-11 Voltage: 400 VAC Frequency: 50 Hz Voltage dip: 70 % 40 % 0 % Number of periods: 25 periods 10 periods 1 period Comments: Criterion A Emitted interference Standards/regulations: EN61000-6-3 Radio interference voltage in acc. with EN 55011: EN55011 (EN55022) ClassB, area of application: Industry and residential Emitted radio interference in acc. with EN 55011: EN 55011 (EN 55022) Class B, area of application: Industry and residential Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself. Criterion C: Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements. |
Di seguito alcuni articoli correlati a quello che stai vedendo
