Automazione Industriale

Meccatronica

Sicurezza Industriale

Componenti Quadri

Sensori e Sistemi di Visione

Pneumatica

Network e Comunicazione

Cavi Speciali

Software di progettazione

Accedi ai servizi

Entra nella tua area riservata

Accedi ai servizi

Entra nella tua area riservata

PHOENIX CONTACT 2961341
PHOENIX CONTACT 2961341
PHOENIX CONTACTNon disponibile

REL-MR- 24DC/1IC - Single relay

Pluggable miniature power relay, with power contact for high switch-on currents up to 130A peaks, 1 N/O contact, input voltage: 24VDC
Cod. Articolo: 2961341
Cod. Fornitore: 2961341
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Caratteristiche Tecniche
Download
Caratteristiche Tecniche
Product propertiesProduct type: Single relay
Operating mode: 100% operating factor
Mechanical service life: 3x 107 cycles
Insulation characteristics
Insulation: Safe isolation, reinforced insulation
Insulation characteristics​
Insulation: Safe isolation, reinforced insulation
Overvoltage category: III
Pollution degree: 3
Electrical propertiesMaximum power dissipation for nominal condition: 0.41 W
Test voltage (Winding/contact): 5 kV AC (50Hz, 1min., winding/contact)
Rated insulation voltage: 250 VAC
Rated surge voltage: 6 kV
Input dataCoil side
Nominal input voltage UN: 24 VDC
Input voltage range: 19.2 VDC ... 54 VDC
Input voltage range in reference to UN: see diagram
Drive and function: monostable
Drive (polarity): non-polarized
Typical input current at UN: 17 mA
Typical response time: 8 ms
Typical release time: 3 ms
Coil resistance: 1440 Ω ±10% (20°C)
Output dataSwitching
Contact switching type: 1 N/O contact
Type of switch contact: Single contact
Contact material: AgSnO
Maximum switching voltage: 250 V AC/DC
Minimum switching voltage: 12 V (100 mA)
Limiting continuous current: 16 A
Maximum inrush current: 80 A (20ms)
130 A (peak, at capacitive load, 230 V AC, 24 μF)
Min. switching current: 100 mA (at 12 V DC)
Interrupting rating (ohmic load) max.: 384 W (at 24 V DC)
58 W (at 48 V DC)
48 W (at 60 V DC)
50 W (at 110 V DC)
80 W (at 220 V DC)
4000 VA (for 250 V AC)
Switching capacity min.: 1200 mW
Switching capacity: 2 A (at 24 V, DC13)
0.2 A (at 110 V, DC13)
0.2 A (at 250 V, DC13)
6 A (at 24 V, AC15)
6 A (at 120 V, AC15)
6 A (at 250 V, AC15)
Motor load according to UL 508: 1/2HP, 120VAC (N/O contact)
1HP, 250VAC (N/O contact)
Connection dataConnection method: Plug / solder connection
DimensionsDimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/123c891effd42443823545fef3d6edf2/-S204x204-FJPG
Width: 12.7 mm
Height: 29 mm
Depth: 15.7 mm
Environmental and real-life conditionsAmbient conditions
Degree of protection: RT II
Ambient temperature (operation): -40°C ... 85°C
Ambient temperature (storage/transport): -40°C ... 85°C
Altitude: ≤ 2000 m
ApprovalsCorrosive gas test
Identification: ISA-S71.04. G3 Harsh Group
EN60068-2-60
Standards and regulationsStandards/regulations: EN50178
EN61810-1
MountingMounting type: Plug-in mounting
Assembly instructions: Can be aligned without spacing (> 70°C ≥ 2.5 mm)
Mounting position: any
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Application_note_00002.pdf

Application_note_00006.pdf

Approvals_00008.pdf

Product_information_00033.pdf

Product_information_00801.pdf

Technical_drawing_41375.pdf