Automazione Industriale

Meccatronica

Sicurezza Industriale

Componenti Quadri

Sensori e Sistemi di Visione

Pneumatica

Network e Comunicazione

Cavi Speciali

Software di progettazione

Accedi ai servizi

Entra nella tua area riservata

Accedi ai servizi

Entra nella tua area riservata

PHOENIX CONTACT 2941183
PHOENIX CONTACT 2941183
PHOENIX CONTACTNon disponibile

DEK-REL- 5/I/1 - Relay Module

Relay terminal block, with soldered-in miniature relays, contact (AgNi+Au): small to medium loads, 1 N/O contact, input voltage 5 V AC/DC, for assembly on NS 35/7.5, terminal width 6.2 mm
Cod. Articolo: 2941183
Cod. Fornitore: 2941183
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Caratteristiche Tecniche
Download
Caratteristiche Tecniche
NotesGeneral: Use of EB 80-DIK... bridges in the DEK terminal blocks: Absorption of humidity from the ambient air as well as an unfavorable tolerance between a larger number of DEK terminal blocks and the EB 80-DIK... bridge may cause (minor) expansion of the DEK housing. When the EB 80-DIK... bridges are used, therefore, it is recommended that these be disconnected after about 10 to 12 DEK terminal blocks and a wire bridge to the next DEK terminal block be inserted in their place.
Product propertiesProduct type: Relay Module
Product family: DEK
Application: Output function
Operating mode: 100% operating factor
Mechanical service life: approx. 2x 107 cycles
Insulation characteristics
Insulation: Basic insulation
Insulation characteristics​
Insulation: Basic insulation
Overvoltage category: III
Pollution degree: 2
Electrical propertiesMaximum power dissipation for nominal condition: 0.12 W
Test voltage (Winding/contact): 2 kV AC (50Hz, 1min., winding/contact)
Input dataCoil side
Nominal input voltage UN: 5 V AC/DC
Input voltage range: 4.5 V AC/DC ... 5.5 V AC/DC (20°C)
Drive and function: monostable
Drive (polarity): polarized
Typical input current at UN: 23 mA
Typical response time: 8 ms
Typical release time: 15 ms
Protective circuit: Bridge rectifier; Bridge rectifier
Operating voltage display: Yellow LED
Output dataSwitching
Contact switching type: 1 N/O contact
Type of switch contact: Double contact
Contact material: AgNi, hard gold-plated
Maximum switching voltage: 250 VAC
125 VDC
Minimum switching voltage: 0.1 V
Limiting continuous current: 3 A (5 A up to 35°C at 24 V DC)
Maximum inrush current: 5 A
Min. switching current: 1 mA
Interrupting rating (ohmic load) max.: 72 W (at 24 V DC)
60 W (at 48 V DC)
50 W (at 60 V DC)
50 W (at 110 V DC)
750 VA (for 250 V AC)
120 W (at 24 V DC - up to 35°)
Connection dataConnection method: Screw connection
Stripping length: 8 mm
Screw thread: M3
Conductor cross section rigid: 0.2 mm² ... 2.5 mm²
Conductor cross section flexible: 0.2 mm² ... 2.5 mm²
Conductor cross section AWG: 24 ... 14
Tightening torque: 0.5 Nm
DimensionsWidth: 6.2 mm
Height: 80 mm
Depth: 56 mm
Environmental and real-life conditionsAmbient conditions
Ambient temperature (operation): -20°C ... 50°C
Ambient temperature (storage/transport): -20°C ... 70°C
Standards and regulationsStandards/regulations: IEC 60947-5-1
MountingMounting type: DIN rail mounting
Assembly instructions: in rows with zero spacing
Mounting position: any
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Application_note_00002.pdf

Application_note_00006.pdf

Manufacturer_declaration_00663.pdf

Manufacturer_declaration_03041.pdf

Manufacturer_declaration_04124.pdf

Manufacturer_declaration_04127.pdf

Manufacturer_declaration_16694.pdf

Package_slip_00897.pdf

Product_information_00033.pdf

Product_information_00772.pdf

Technical_drawing_41223.pdf