Automazione Industriale

Meccatronica

Sicurezza Industriale

Componenti Quadri

Sensori e Sistemi di Visione

Pneumatica

Network e Comunicazione

Cavi Speciali

Software di progettazione

Accedi ai servizi

Entra nella tua area riservata

Accedi ai servizi

Entra nella tua area riservata

PHOENIX CONTACT 2903696
PHOENIX CONTACT 2903696
PHOENIX CONTACTNon disponibile

REL-OR3/L-230AC/3X21 - Single relay

Plug-in octal relays with power contacts, 3 changeover contacts, test button, mechanical switching position indicator, input voltage: 230 V AC
Cod. Articolo: 2903696
Cod. Fornitore: 2903696
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Caratteristiche Tecniche
Download
Caratteristiche Tecniche
NotesGeneral: The outputs are not suitable for switching different outer conductors.
Do not use to separate SELV / PELV circuits from other circuits, because safe isolation is not guaranteed.
Product propertiesProduct type: Single relay
Operating mode: 100% operating factor
Mechanical service life: approx. 2x 107 cycles
Insulation characteristics
Insulation: Basic insulation
Insulation characteristics​
Insulation: Basic insulation
Overvoltage category: III
Pollution degree: 3
Electrical propertiesService life electrical: see diagram
Maximum power dissipation for nominal condition: 2.99 W
Test voltage (Winding/contact): 2.5 kVrms (50Hz, 1min., winding/contact)
Test voltage (Changeover contact/changeover contact): 2.5 kVrms (50Hz, 1min., changeover contact/changeover contact)
Rated insulation voltage: 250 VAC
Rated surge voltage: 4 kV
Input dataCoil side
Nominal input voltage UN: 230 VAC
Input voltage range: 195.5 VAC ... 253 VAC (20°C)
Mains frequency: 50/60 Hz
Drive and function: monostable
Drive (polarity): non-polarized
Typical input current at UN: 13 mA
Input power dissipation for UN: 2.6 W
Typical response time: 5 ms ... 15 ms (depending on phase relation)
Typical release time range: 5 ms ... 20 ms (depending on phase relation)
Status display: Yellow LED
Coil resistance: 7080 Ω ±15%
Output dataSwitching
Contact switching type: 3 changeover contacts
Type of switch contact: Single contact
Contact material: AgNi
Maximum switching voltage: 250 VDC
440 VAC
Minimum switching voltage: 10 V (At 24 mA)
Limiting continuous current: 10 A
Maximum inrush current: 30 A (20 ms, N/O contacts)
Min. switching current: 10 mA (at 24V)
Interrupting rating (ohmic load) max.: 240 W (at 24 V DC)
124 W (at 48 V DC)
108 W (at 60 V DC)
52 W (at 110 V DC)
48 W (at 220 V DC)
2500 VA (for 250 V AC)
Connection dataConnection method: Plug-in connection
DimensionsWidth: 35 mm
Height: 35 mm
Depth: 54.4 mm
Environmental and real-life conditionsAmbient conditions
Degree of protection: RT I
Degree of protection (Installation location): ≥ IP54 (Installation location)
Ambient temperature (operation): -40°C ... 55°C
Ambient temperature (storage/transport): -40°C ... 85°C
Altitude: ≤ 2000 m
ApprovalsCorrosive gas test
Identification: ISA-S71.04. G3 Harsh Group
EN60068-2-60
Standards and regulationsStandards/regulations: IEC 60664
IEC 61810
MountingMounting position: any
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Application_note_00002.pdf

Application_note_00006.pdf

Approvals_00008.pdf

Product_information_00033.pdf

Product_information_00630.pdf

Technical_drawing_39855.pdf