Automazione Industriale

Meccatronica

Sicurezza Industriale

Componenti Quadri

Sensori e Sistemi di Visione

Pneumatica

Network e Comunicazione

Cavi Speciali

Software di progettazione

Accedi ai servizi

Entra nella tua area riservata
Accedi al B2B
Accedi al tuo account

Accedi ai servizi

Entra nella tua area riservata

Accedi al B2B
Accedi al tuo account
Paese|
||Carrello
Technology BSA logo
Logo Rockwell Automation partner - Value Add Distributor
PHOENIX CONTACT 1624784
PHOENIX CONTACT 1624784
PHOENIX CONTACTNon disponibile

K-17-M17 M9/010-E01/M17 F8 - Connector in molded plastic on both sides

Connector in molded plastic on both sides, M17-Socket, Straight, plastic molded, number of positions: 17, type of locking: Screw locking mechanism, on M17-Pin, Straight, plastic molded, number of positions: 17, cable length: 10 m, shielded: yes, color of outer sheath: green, Alternative product in accordance with RoHS II without Exemption6c (Pb<0.1%) item no.: 1261273
Cod. Articolo: 1624784
Cod. Fornitore: 1624784
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Caratteristiche Tecniche
Download
Caratteristiche Tecniche
NotesSafety note
Safety note: • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Only use tools recommended by PhoenixContact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product propertiesProduct type: Signal and power cable
ConnectorConnector specifications
Type: Straight, plastic molded
Housing material: Zinc die-cast
Thread type: M17
Type of locking: Screw locking mechanism
Degree of protection: IP67, when in locked state
No. of pos.: 17
Direction of rotation: Standard
Contact switching type: Socket
Insertion/withdrawal cycles: 50
Contact resistance: < 0.3 mΩ
Max. current: 3.6 A
Voltage: 48 VAC
74 VDC
Overvoltage category: III
Degree of pollution: 3
Rated surge voltage: 1.5 kV
Ambient temperature (operation): -40°C ... 105°C
Cable specifications
Cable type: SSLC11Y
Shielded: yes
Cable structure: 3x2x0.14mm²+2x0.5mm²+4x0.14mm²+4x0.22mm²
Cable structure (AWG): 26 AWG/3pr + 20 AWG/2c + 26 AWG/4c + 24 AWG/4c
External cable diameter: 9.4 mm
Outer sheath, material: TPU
Material wire insulation: TPU
External sheath, color: green
Nominal voltage, cable: 30 V
Test voltage: 0.5 kV
Rated current: 9 A
Smallest bending radius, fixed installation: 38 mm
Smallest bending radius, movable installation: 94 mm
Ambient temperature (operation) for fixed installation: -30°C ... 80°C
Ambient temperature (operation) for flexible installation: -30°C ... 60°C
Connector specifications (second page)
Type: Straight, plastic molded
Housing material: Zinc die-cast
Thread type: M17
Degree of protection: IP67, when in locked state
No. of pos.: 17
Direction of rotation: Standard
Contact switching type: Pin
Insertion/withdrawal cycles: 50
Contact resistance: < 0.3 mΩ
Max. current: 3.6 A
Voltage: 48 VAC
74 VDC
Overvoltage category: III
Degree of pollution: 3
Rated surge voltage: 1.5 kV
Ambient temperature (operation): -40°C ... 105°C
Electrical propertiesNominal current IN: 3.6 A
Cable/lineCable length: 10 m
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Manufacturer_declaration_03363.pdf

Manufacturer_declaration_03811.pdf

Manufacturer_declaration_05486.pdf

Manufacturer_declaration_12807.pdf