Automazione Industriale

Meccatronica

Sicurezza Industriale

Componenti Quadri

Sensori e Sistemi di Visione

Pneumatica

Network e Comunicazione

Cavi Speciali

Software di progettazione

Accedi ai servizi

Entra nella tua area riservata
Accedi al B2B
Accedi al tuo account

Accedi ai servizi

Entra nella tua area riservata

Accedi al B2B
Accedi al tuo account
Paese|
||Carrello
Technology BSA logo
Logo Rockwell Automation partner - Value Add Distributor
PHOENIX CONTACT 1607509
PHOENIX CONTACT 1607509
PHOENIX CONTACTNon disponibile

VC-AML 4 - Contact insert

Contact insert, Range of articles: VARIOCON, design: VC2, housing material: PA, color: light grey, number of positions: 4, rated voltage: 690, rated current: 63 A, Connection method: PCB connection, Contact connection type: Pin. Connectors may only be connected/disconnected when under no load.
Cod. Articolo: 1607509
Cod. Fornitore: 1607509
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Caratteristiche Tecniche
Download
Caratteristiche Tecniche
NotesGeneral: Connectors may only be connected/disconnected when under no load.
Safety note
Safety note: WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by PhoenixContact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product propertiesType: VC2
Product type: Contact insert
Product family: VARIOCON
Number of positions: 4
Connection profile: 3+PE
Number of module slots: 3
Series: VC-M
Insulation characteristics
Degree of pollution: 3
Electrical propertiesRated voltage (II/2): 1000 V
Rated voltage (III/2): 1000 V
Rated voltage (III/3): 690 V
Nominal voltage ATD: 690
Rated surge voltage: 6 kV
Rated surge voltage (II/2): 8 kV
Rated surge voltage (III/2): 8 kV
Rated surge voltage (III/3): 8 kV
Rated current: 63 A
70 A
63 A
Nominal voltage UN: 690 V
DimensionsDimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/9c3f8142854dda43a08845e4da363997/-S204x204-FJPG
Width: 45 mm
Height: 23.1 mm
Length: 35.6 mm
Material specificationsColor: light grey
Color of the housing part: gray
Material: Polyamide
Flammability rating according to UL 94: V0
Insulating material group: I
Contact material: E-Cu 58
Contact surface material: hard-silver plated
Contact carrier material: PA
Housing material: PA
Cable/lineHalogen-free: yes
Mechanical propertiesMechanical data
Insertion/withdrawal cycles: ≥ 50
Environmental and real-life conditionsAmbient conditions
Ambient temperature (operation): -40°C ... 100°C
MountingConnection method: PCB connection
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Application_note_00208.pdf

Technical_drawing_16888.pdf