Automazione Industriale

Meccatronica

Sicurezza Industriale

Componenti Quadri

Sensori e Sistemi di Visione

Pneumatica

Network e Comunicazione

Cavi Speciali

Software di progettazione

Accedi ai servizi

Entra nella tua area riservata
Accedi al B2B
Accedi al tuo account

Accedi ai servizi

Entra nella tua area riservata

Accedi al B2B
Accedi al tuo account
Paese|
||Carrello
Technology BSA logo
Logo Rockwell Automation partner - Value Add Distributor
PHOENIX CONTACT 1050771
PHOENIX CONTACTNon disponibile

PV-C1F-C-HSG - Photovoltaic connector

Photovoltaic connector, Range of articles: Sunclix, housing material: PPE, color: black, number of positions: 1, min. conductor cross section: 2.5 mm2, max. conductor cross section: 6 mm2, rated voltage: 1500 V DC, rated current: 40 A, Connection method: Crimp, Contact connection type: Socket, min. cable diameter: 5 mm, max. cable diameter: 8 mm
Cod. Articolo: 1050771
Cod. Fornitore: 1050771
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Caratteristiche Tecniche
Download
Caratteristiche Tecniche
NotesSafety note
Safety note: • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
• Operate the connector only when it is fully plugged in and interlocked.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
Product propertiesProduct type: Photovoltaic connector
Product family: Sunclix
Number of positions: 1
Insulation characteristics
Protection class: II
Degree of pollution: 2
Electrical propertiesRated voltage (II/2): 1500 V
Nominal voltage ATD: 1500 V DC (II/2) in accordance with IEC 62852:2014/AMD1:2020
1500 V DC in accordance with UL6703
Rated surge voltage: 16 kV
Rated surge voltage (III/3): 16 kV
Rated current: 40 A (in accordance with IEC 62852:2014/AMD1:2020)
50 A (in accordance with UL6703)
35 A (in accordance with UL6703)
30 A (in accordance with UL6703)
Rated current (4.0 mm²): 34 A (in accordance with IEC 62852:2014/AMD1:2020)
Rated current (2.5 mm²): 27 A (in accordance with IEC 62852:2014/AMD1:2020)
Contact resistance: ≤ 0.45 mΩ
< 0.3 mΩ (Crimp to crimp)
DimensionsWidth: 20 mm
Height: 20 mm
Length: 72.8 mm
Material specificationsColor: black
Color of the housing part: black
Flammability rating according to UL 94: V0
Insulating material group: II
Insulating material: mPPE
Cable seal material: EPDM
Contact material: Cu
Contact surface material: Ag
O-ring material: Silopren LSR 2660
Housing material: PPE
Cable/lineCable type: H1Z2Z2-K lines
External cable diameter (): 5 mm ... 8 mm
External cable diameter: 5 mm ... 8 mm
Single wire, cross section: 2.5 mm² 6 mm² 14 AWG 10 AWG
Stripping length of the individual wire: 9 mm -1mm
Cable pull-out force: > 80 N (IEC 62852:2014)
Mechanical propertiesOutside conductor diameter: 5 mm 8 mm
Mechanical data
Outside conductor diameter: 5 mm 8 mm
Insertion/withdrawal cycles: 100
Insertion force: 45 N ±10N
Withdrawal force: 250 N ±50N (when locked)
Environmental and real-life conditionsAmbient conditions
Degree of protection: IP66 /IP68 (2 m / 24 h) (plugged in)
IP20 (Not plugged in)
IP66 / IP68 (2 m / 24 h)
Ambient temperature (operation): -40°C ... 85°C (dependent on the derating curve)
Ambient temperature (assembly): -5°C ... 50°C
Standards and regulationsStandards/specifications: IEC 62852:2014/AMD1:2020
MountingConnection method: Crimp
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Manufacturer_declaration_01383.pdf

Manufacturer_declaration_02321.pdf

Package_slip_02026.pdf

Package_slip_02028.pdf

Technical_drawing_06684.pdf